Tutor Platform

AA.III.I.S4

Skill

Coordinate with crew, if applicable, and complete the appropriate procedures, checklist(s), and radio calls following a rejected takeoff in a timely manner.

Study note

Get a short, cited explanation of this element written from the FAA handbooks: the core idea, the numbers that matter, common test traps, and a quick self-check.

Sign in to generate a study note

From the FAA library

  • Chapter 16: Transition to Jet-Powered Airplanes › Jet Airplane Takeoff and Climb › Rejected Takeoff

    takeoff and climb-out should be accomplished in accordance with a standard takeoff and departure profile developed for the particular make and model airplane. [Figure 16-13] Figure 16-13. Sample takeoff and departure profile. The pilot not flying should ... call out V1. After passing V1 speed on the takeoff roll, it is no longer mandatory for the pilot flying to keep a hand on the thrust levers. The point for abort has passed, and both hands may be placed…

  • Chapter 11: Aircraft Performance › Takeoff and Landing Performance › Takeoff Performance

    Figure 11-19 illustrates the general effect of wind by the percent change in takeoff or landing distance as a function of the ratio of wind velocity to takeoff or landing speed. The effect of proper takeoff speed is especially ... important when runway lengths and takeoff distances are critical. The takeoff speeds specified in the AFM/POH are generally the minimum safe speeds at which the aircraft can become airborne. Any attempt to take off below the recommended speed means that…

  • Chapter 16: Transition to Jet-Powered Airplanes › Jet Airplane Takeoff and Climb › Takeoff Roll

    pilot not flying. Retarding a thrust lever would only be necessary in case an engine exceeds any limitation. Takeoff data, including V1/VR and V2 speeds, takeoff power settings, and required field length should be computed prior to each takeoff ... make and model without an FMS, the data should be recorded on a takeoff data card. This data is based on airplane weight, runway length available, runway gradient, field temperature, field barometric pressure, wind, icing conditions, and runway condition. Both…

  • Chapter 6: Takeoffs and Departure Climbs › Crosswind Takeoff › Takeoff Roll

    Crosswind Takeoff While it is usually preferable to take off directly into the wind whenever possible or practical, there are many instances when circumstances or judgment indicate otherwise. Therefore, the pilot must be familiar with the principles and techniques involved ... crosswind takeoffs, as well as those for normal takeoffs. A crosswind affects the airplane during takeoff much as it does during taxiing. With this in mind, the pilot should be aware that the technique used for crosswind correction during takeoffs…

  • Chapter 16: Transition to Jet-Powered Airplanes › Jet Airplane Takeoff and Climb › V-Speeds

    Airplane Takeoff and Climb The following information is generic in nature and, since most civilian jet airplanes require a minimum flight crew of two pilots, assumes a two-pilot crew. If any of the following information conflicts with FAA-approved ... procedures for a particular airplane, the AFM procedures take precedence. Also, if any of the following procedures differ from the FAA-approved procedures developed for use by a specific air operator and/or for use in an FAA-approved training center…

  • 14 CFR Part 141, Appendix J to Part 141—Aircraft Type Rating Course, For Other Than an Airline Transport Pilot Certificate

    Airline Transport Pilot Certificate (1) A type rating for an airplane—single-engine course: (i) Preflight preparation; (ii) Preflight procedures; (iii) Takeoff and departure phase; (iv) In-flight maneuvers; (v) Instrument procedures; (vi) Landings and approaches to landings; (vii) Normal ... abnormal procedures; (viii) Emergency procedures; and (ix) Postflight procedures. (2) A type rating for an airplane—multiengine course: (i) Preflight preparation; (ii) Preflight procedures; (iii) Takeoff and departure phase; (iv) In-flight maneuvers; (v) Instrument procedures; (vi) Landings and approaches…